XeNTaX

Still ahead of tool which output model with materials, Lamborghini made for Assetto Corsa, in total, guys: manually carved out lods, meshes taken using version j. Known issues (most likely the same on many models), wipers, not all, only 1(but real lambo have 2 variations), dashpad wrong scale and position (also was attached to steeringwheel), model is mirrored, door speakers have some unknown mesh in there. UPD. Thank you guys again for work on it.

Found on vk

Found on my HDD

hope, version j2 will make texturing a lot easier (no manual grouping required)
This was possible because of the amazing work of Andrakann!

WARNING: split your filelist into exterior and interior for example
or you'll experience a significant blender slow down because of too many groups.

For BMW_i8_15, exterior, for example, automatic grouping seems to be ok.

All LOD submeshes are separated but you've to select the LODs manually,
for example DB11, taillightL, LODS0 and LOD1:

LODS0: taillightL_a_000 to taillightL_a_005
LOD1: taillightL_a_006 to taillightL_a_011

Few uv maps and AUD_Quattro dashstructure for example still spoiled.

javadst wrote:Hi.
All imported models are mirrored !

Hi, if you sent me the concerning modelbin file I could have a look at.

@shakotay2

I just tested the J2 version on the Audi RS2. I get an error saying "too many faces in AUD_RS2_95_skeleton.modelbin, then I get the standard Windows "*exe* has stopped working" message.

Here's the file it complained about if you want to investigate.
http://www106.zippyshare.com/v/hilidufB/file.html

TheAdmiester wrote:@shakotay2

I just tested the J2 version on the Audi RS2. I get an error saying "too many faces in AUD_RS2_95_skeleton.modelbin, then I get the standard Windows "*exe* has stopped working" message.

Here's the file it complained about if you want to investigate.

thx; I didn't care for the skeleton.modelbins so far.
But sure, at least it should tell this instead of giving such confusing message.

shakotay2 wrote:

TheAdmiester wrote:@shakotay2

I just tested the J2 version on the Audi RS2. I get an error saying "too many faces in AUD_RS2_95_skeleton.modelbin, then I get the standard Windows "*exe* has stopped working" message.

Here's the file it complained about if you want to investigate.

thx; I didn't care for the skeleton.modelbins so far.
But sure, at least it should tell this instead of giving such confusing message.

Sorry, it was my mistake to try and use the whole scene folder instead of trying to delete what wasn't used.

Removing it works perfectly though, thanks.

Grouping looks spot on so far. Will test with some others.
Thanks Andrakann and shakotay2.

EDIT1: Interior groups are okay on the SVR. Still had to scale the top of the dash and steering column which is a 1 min job as the scaling is joined between the pair.
EDIT2: Ran into a problem with the Ferrari 355 doorLF_a.modelbin just crashes when trying to load the modelbins.txt.
http://www.mediafire.com/file/09g1ybr12 ... a.modelbin

minime891 wrote:EDIT2: Ran into a problem with the Ferrari 355 doorLF_a.modelbin just crashes when trying to load the modelbins.txt.

thx for reporting; well that's a "release only" bug that is hard to spot.
[fixed]

Excellent work. You are close to perfection. Thank you again for all your great work.
How is going doors position thing?

BTW. why FH3 models are much bigger than previous forza models? what is the scale that you use?

TomWin wrote:Excellent work. You are close to perfection. Thank you again for all your great work.
How is going doors position thing?

BTW. why FH3 models are much bigger than previous forza models? what is the scale that you use?

On import the scale i use is 0.7813. As you can see in the picture below it's spot on with the old forza model.
I have only done this with the BMW 1M so far but if they all use the same reference for the scale they should all be fine i suppose.

minime891 wrote:

TomWin wrote:Excellent work. You are close to perfection. Thank you again for all your great work.
How is going doors position thing?

BTW. why FH3 models are much bigger than previous forza models? what is the scale that you use?

On import the scale i use is 0.7813. As you can see in the picture below it's spot on with the old forza model.
I have only done this with the BMW 1M so far but if they all use the same reference for the scale they should all be fine i suppose.

Thank you. yeah apparently it works fine for all cars.


EDIT: The Make_H2O-ForzaHor3 crash when I'm trying to convert FOR_FocusRS_03

shakotay2 wrote:Hi, if you sent me the concerning modelbin file I could have a look at.

Hi, BMW M6 front badge (Mirrored).

mirroring and scaling applied as suggested.

minime891 wrote:On import the scale i use is 0.7813. As you can see in the picture below it's spot on with the old forza model.

dunno, if you know: 0.078125 = 200.0/256.0, btw

Since a scale of 0.02 was my suggested scale for blender import I used 4.0/256.0 now. [edit]

TomWin wrote:How is going doors position thing?

well, this is going to eat my time up.
I had been hoping someone else (other than Andrakann and me) would take up the skeleton.modelbin analysing for example.
(It's small files so should not be too hard.)

The more annoying thing is the remaining uv issues, but that would need more time/motivation to solve: So next thing on the list is the material names.

@shakotay2 Did you plane, updata your tool with lods extracted?